The solution for the defective pieces of the automatic cutting machine that needs to be re-cut

The solution for the defective pieces of the automatic cutting machine that needs to be re-cut

In recent years, equipment automation has become the development trend of enterprises. Various automation equipment has also become a weight for enterprises to participate in competition. When comparing the advantages of automatic cutting over manual cutting, traditional garment factories rely to a large extent on experienced masters to estimate the fabric required for each order, and those who need to be transferred between the cutting room, the printing room and the raw materials The data is usually entered manually, so errors are common.

This is the disadvantage of manual operation. Automation can solve exactly these problems. So how to solve the defective products produced by the cutting machine with a high CAD penetration rate in Canada? The solutions are as follows:

If a piece is not cut well, or there is a defect on the piece that needs to be re-cut, single-piece re-cut can be used.

Operation steps: Open the layout map where the piece is located, and select Single piece recut in the recovery menu. At this time, a single piece recut dialog box will pop up. Enter the number of the piece to be recut in the dialog box, and then click OK. Pieces are displayed individually on the layout screen. Fix the fabric on the cutting table, move the cutting head to the lower left corner of the cutting area, and set the origin, then click to cut.

The solution to retrieve cutting information after emergency stop

Restore the origin.

After an emergency stop event occurs, it is necessary to restore the origin so that the cutting machine can continue to cut. Operation steps to restore the origin: Open the C-200MT software, find the restore origin in the restore menu, and click to restore the origin. The restored origin data can be seen in the two-line output display column of the C-200MT software.



Servo can not be turned on the solution

There are generally two reasons why the servo cannot be turned on: one is that the power supply is not connected, you should check whether the power switch, circuit breaker, etc. are in the ON position; the other is that the cutting head runs out. In addition, it is not excluded that after the cutting machine is turned on, there is no initialization, so that the cutting head is thrown out of the designated area and the servo cannot be turned on. The solution is to move the cutting head or beam to the middle part of the cutting table by hand; or pull the belt to make the cutting head or beam to the middle part of the cutting table.



The solution for the vacuum level not meeting the parameter requirements

During the cutting process, the cutter uses a vacuum to hold the fabric firmly on the cutting table. When the vacuum level does not meet the requirements, the cutter cannot cut. It should be checked whether the plastic sheet on the fabric is in good condition and whether it completely covers the entire fabric area. Only when the entire fabric area is completely covered can the vacuum level meet the parameter requirements. If the plastic sheet is damaged during the cutting process, you can add another piece of plastic sheet to cover.



Do not know the solution to whether the width of the cutting fabric can meet the requirements

Check the cloth width. After determining the origin, in order to confirm whether the fabric width meets the requirements, in the C-20MT software, press CTRL+W key, the cutting head moves to the other end of the fabric, and observe whether the fabric width meets the requirements.

The solution to the uneven edge of the fabric

Cut manually.

When the edge of the fabric is not neat, the manual cutting function can be used to cut the fabric neatly. Operation steps: Press the manual cutting button in the beam control panel, when the status light flashes, press the rotary switch and operate the joystick at the same time to complete the cutting operation.

The solution to the deflection of the fabric when too much material is fed through the window

Fabric slope control.

During the cutting process, if there are too many windows (the cutting fabric is long), the fabric may be skewed during feeding, and if it is not corrected in time, unforeseen consequences will occur. How to control this situation? In general, a red tape of 0.3-0.5 cm wide or a ruler with thickness can be pasted between A and B, and the fabric can be aligned here before cutting after passing through the window.

Official website: www.wxyh888.com

Alibaba official website:

http://wxjyfr.cn.1688.com/

Taobao official website:

http://wxyh888.taobao.com/